Today is launch date for Apple’s new iPhone 7 models, and as is tradition every year, the teardowns have already begun. Both the Chipworks/TechInsights team and iFixit have completed their respective initial teardowns of the iPhone 7 and 7 Plus, tearing part some of the first phones to go on sale. These teardowns are preliminary – there’s a lot of work left to do in deciphering the many cryptic identification numbers of the various components – but right off the bat it confirms a few things about each of the phones.

We’ll start off with the Chipworks teardown of an iPhone 7, which they have already earnestly begun identifying chips on. One of their immediate findings is that for the first time in a while, Apple is using a non-Qualcomm modem. On Chipworks’ GSM phone, they have found an Intel baseband processor with the model number PMB9943. They believe this to be part of Intel’s XMM 7360 modem, which was announced back in 2015.

The XMM 7360 is a high-end LTE Advanced modem design that offers up to Category 10 performance (450 Mbps down). This is achieved in part through the use of 3x carrier aggregation, which allows the modem to use up to 60Mhz of wireless spectrum. The modem does not support CDMA, and as the iFixit team has turned up a Qualcomm Snapdragon X12 (Cat 12) modem in their unit, Apple is clearly using modems from multiple vendors. It’s not clear how this breakdown works – if Apple is using the Qualcomm modem in some GSM phones as well – but at a minimum the Qualcomm modem will have to be in all of the CDMA-capable models.

Meanwhile for Intel’s modem group, this is a significant win, as the company has not seen too many high-profile device wins in recent years. Though historically speaking, this is actually something of a return to form. The original iPhone used a modem from the group’s predecessor, Infineon’s wireless unit, whom Intel purchased in 2010.

Moving on, we have of course the A10 Fusion SoC. Chipworks has yet to get a die shot in, but they have already confirmed that the SoC is produced by TSMC. This is presumably another 16nm FinFET SoC, but the Chipworks team will be working to confirm that. So far there is no evidence to indicate that Apple is dual-sourcing SoCs on the iPhone 7 like they did the iPhone 6s, but this is again preliminary information.

Given that Apple doesn’t get a major new manufacturing process to use this generation, I had been wondering if and how Apple would instead compromise on die size, and we now have a rough answer. Chipworks estimates the A10 die to be roughly 125mm2 in size. This is 20.5mm2 (~20%) larger than the A9 TSMC die. The good news for Apple is that yields should be much better in 2016 than they were in 2015, so chip manufacturing costs should be down, helping to offset the higher costs of the larger chip. And while there are ways to improve performance without increasing the die size, any kind of significant improvement would have to entail a larger die, which is exactly what we’re seeing here. If nothing else, Apple would need more room for the new high-efficiency CPU cores the chip packs in.

Speaking of packing, Chipworks’ teardown also hints that the A10 may have been packaged using TSMC’s new Integrated Fan Out (InFO) technique, which is meant to allow for thinner chip packages. InFO saves space, in part, by eliminating the organic substrate that logic dies have traditionally been mounted on.

Lastly with the A10, Chipworks’ teardown of their iPhone 7 confirms that it has 2GB of RAM, specifically Samsung LPDDR4. Besides confirming that the memory capacity on the iPhone 7 hasn’t increased versus the iPhone 6s, this is notable because iFixit has found something different with their iPhone 7 Plus. In the case of the larger phone, there is 3GB of RAM. Apple has never before equipped the Plus with more memory than the base model, so this is a first. And while there has always been some performance stratification between the two phones due to the Plus model’s larger size – allowing better heat dissipation, and therefore slightly better performance – I wonder if this means we’re going to see an increase in the stratification between the two phone models. If nothing else, I suspect this comes as a consequence of the Plus’s higher resolution screen: all other factors being held equal, the Plus needs a bit more RAM for its larger GPU frame buffers.

Update: The Chipworks crew has their die shot and floor plan back, so let's take a look.

As Apple already disclosed the number of GPU clusters, there's not a whole lot left to doubt in terms of basic construction.The GPU cores, SRAM caches, and the performance CPU cores are all easy enough to find, with the latter block now about 16mm2, versus 13mm2 in the A9. The big question here is where the two smaller, high-efficiency cores are. Chipworks postulates three thories: 1) They're in the same block as the high performance cores (and hence labeled as a quad core CPU), they're to the left of the die, or they're to the bottom left of the die.

It is likely - but not guaranteed - that they're close to the high-performance cores. However both alternative locations do have pairs of identical blocks, which is what you'd be looking for in a secondary set of CPU cores. So although those options are less likely, without additional information it's difficult to rule out those options entirely.

Finally, one interesting aspect of the Chipworks report is that they unexpectedly found a third audio amplifier. Chipworks was expecting to find two – one for each of the speakers – but came up with a third. The firm believes that the third amp may be for headphones, which in turn would mean that Apple has significantly revised the Lightning port specification for the iPhone 7. Previously Lightning has only carried digital audio, which doesn’t require an amp in the phone itself. In the initial iPhone 7 announcement I had speculated that Apple put the DAC (and amp) inside their 3.5mm adapter – which would be consistent with how Lightning has worked over the last 4 years – but this casts doubt on that idea. If Apple has revised the specification to allow analog audio over the port, then this greatly simplifies how headphones and adapters will work. But it also would raise a number of questions about peripheral compatibility, especially what happens if you plug something like the Lightning EarPods into an older device like the iPhone 5s.

On that note, the Chipworks and iFixit teardowns also show us what’s gone in the place of the now-absent headphone jack: Apple has placed a taptic engine (linear actuator) for the solid state home button, and an unusual plastic bumper.

Wrapping things up, Chipworks’ reports that they already have the A10 SoC in their lab for further work, including confirming the manufacturing process and, of course, a die shot. The latter should prove to be very interesting, as it will be the first look we get at Apple’s new high-efficiency CPU cores. And in the meantime on our end we also have our iPhone samples in-house, so we’re diligently working on putting together a review for later this month. So be sure to stay tuned for that.

Sources & Images Courtesy: Chipworks & iFixit

Comments Locked


View All Comments

  • bebaile - Friday, September 16, 2016 - link

    Well in that space, and although limited to most dense areas, things are moving fast as the launch of LTE-Advanced Pro networks in several countries in 2016 has shown and by the end of the year 1 Gbps network services should be launched in most advanced market (either with the help of unlicensed spectrum or not).

    Besides the point is not to say that people individually need 600 mbps throughput, just that the higher the maximum throughput, the higher the average throughput so yes it matters in the end. I admit that from a commercial point of view, users will be equally happy next year or the year after when they will see that their iPhone is capable of 600 Mbps since that capability will have been deployed in more network but as a user i prefer to make an enlightened choice between a Qualcomm based iPhone 7 and an Intel based iPhone 7.
  • sonicmerlin - Friday, September 16, 2016 - link

    Why does it feel like I'm the only one annoyed we now have GSM only and CDMA only iPhones? Apple went backwards. My 6S is a nearly global phone that can be used on almost any network, and makes switching between American carriers extremely easy.

    Why would Apple give itself more work in terms of managing radio firmware and device models?
  • mkozakewich - Friday, September 16, 2016 - link

    If you buy one unlocked, you'll undoubtedly get the Qualcomm one. The Intel chip was probably cheaper, and would end up in all the carrier-locked versions on GSM networks.
  • name99 - Friday, September 16, 2016 - link

    Why indeed...
    As always the internet is obsessed with the shiny ("ooh, no headphone jack") and incapable of looking at the big picture.

    Apple is already now shipping a custom wireless chip. Yes, it's (apparently) BT only (though if it supports BT3, it may also have a WiFi element to it). But moving wireless processing onto their SoC, and having a wireless portfolio, has long been an obvious move in terms of reducing space and giving them another place where they can try to control power and provide new experiences outside the constraints of how QC thinks wireless should be done.

    So how do they get access to those wireless patents and know-how? Sometimes you have to take one for the team, and in this case taking one means making a deal with Intel. "We'll buy your modem, we'll accept the flack that comes from people saying it's inferior (both by specs, and perhaps, by performance), we'll put up with the SKU hassle. And in return, here's how you will help us"...
  • stlc8tr - Friday, September 16, 2016 - link

    "Why does it feel like I'm the only one annoyed we now have GSM only and CDMA only iPhones?"

    For the US market, you can have a GSM-only iPhone (AT&T/TMobile) and a GSM/CDMA iPhone (Sprint/Verizon). There is no CDMA-only iPhone.
  • iwod - Friday, September 16, 2016 - link

    Its time for Anandtech to do a article on Intel modem as well. After all these years Intel has finally shipped a modem on a Smartphone that Actually has MANY people using it.

    I would really like to know what node is the 7360 fabbed on.
  • Ariknowsbest - Saturday, September 17, 2016 - link

    7360 is most likely fabbed on TSMC 28nm, like the rest of Intels modem.
  • Pneumothorax - Monday, September 19, 2016 - link

    In other words, inferior to Qualcomm. Now we're getting reports that the Intel chipped 7's are having frequent wifi/LTE disconnection issues requiring a reboot. Now why does this sound so familiar?! Hint Hint: many laptops/tablets with Intel wifi issues.
  • Deelron - Friday, September 16, 2016 - link

    It wouldn't be the first time they used different components in a device that had marginally different specs. As long as both modems meet he advertised speed, it's not concerning in that sense.

    I doubt Apple has any strategy given the modem differences, I doubt (in the real world) there will be enough of a noticeable difference in speed to mean anything over a 3 year life cycle, and if it does work out for an individual here or there, great you got a slight bonus
  • stux - Friday, September 16, 2016 - link

    In answer to your question, yes, imo, knowing apples style, they would lock it down to Cat 10 rather than bifurcate the userbase. Also simplifies conformance testing.

    Doesn't mean they have of course

Log in

Don't have an account? Sign up now