In and Around the Cooler Master Cosmos II

Cooler Master's Cosmos II is a big, fairly attractive hunk of steel, aluminum, and plastic. The black finish with blue LED indicators isn't going to light the world on fire with its stunning originality, but the overall styling is actually just under being too gaudy. Gaming and enthusiast cases always run the risk of looking outlandish or ridiculous, but the Cosmos II is mostly able to avoid the same fate. Honestly, what you're really going to notice is the sheer size of the thing.

Unlike most cases, there's something happening on every side of the Cosmos II. The top has two heavy aluminum bars affixed to the case's steel frame, and those bars are designed pretty much exclusively to help you actually move the enclosure. Between them, to the rear is a giant vent made of tough plastic and metal that's designed to support up to a 360mm watercooling radiator. Towards the front is a control panel with four independent fan control channels, an LED toggle, and the power and reset buttons, masked with a sliding plastic hood.

This hood is where I first ran into trouble. Simply put, it's chintzy, and on my review unit it actually broke off. That hood is held in place with two plastic rails, but one of those was damaged when I received the case, and with a minimal amount of force (if I'm complaining about lifting a 50 pound case, trust me when I say "minimal") the whole thing snapped right off.

When we get to the front of the Cosmos II, under that hood there's a healthy amount of connectivity: four USB 2.0 ports, two USB 3.0 ports, an eSATA port, and the two audio jacks. The external drive bays are actually shielded by a cover that is held to the top of the case magnetically but slides down to reveal them. There are three 5.25" bays protected by plastic drive shields, and then two lockable (and removable) 3.5" hot-swap bays. The front vent is also removable by applying some force to the bottom and lifting upward, but the problem is that when moving the Cosmos II, this is going to be one of the places you'd want to grip it.

The sides are both covered with two hinged doors that have steel frames with aluminum finishes and ventilation at the bottom that lines up with six of the internal 3.5" drive bays; these doors open by pressing levers on the back of the case, but they're also easily removable by just lifting them off the hinges once they're open. Finally, the back is fairly mundane, sporting ten expansion slots plus an eleventh off-center one for extra ports or fan control, a single 140mm exhaust fan, and a removable power supply bracket.

The inside of the Cosmos II is just as spacious and copious as its exterior, and it's broken up into two chambers. The top chamber houses the motherboard (up to XL-ATX) along with a drive cage that holds five 2.5"/3.5" drives on sleds and the five 5.25" drive bays (two of which are occupied by Cooler Master's X-Dock 3.5" docking bay). There are a healthy number of rubber-grommeted routing holes in the motherboard tray, allowing for clean cabling for just about any configuration.

There are cut-outs in the metal divider between the top and bottom chambers, but you'll want to route most of the cable bundle back behind the tray. The bottom chamber has two 120mm fans mounted to an internal hinge that blow cool air across six additional 2.5"/3.5" drive sleds, and then the power supply is also mounted down here. Finally, the area behind the motherboard tray is spacious and easy to route cables in.

There's no real reason to expect assembling the Cosmos II to be difficult outside of its sheer mass, so if you're not a crybaby weakling like I am you'll probably have a much better time with it. Where I get concerned is with the use of chintzy plastic in parts of the assembly. The "fins" around the enclosure are easily bendable and I can see them breaking just like the control panel hood did (especially if you try and lift the case up by them), and while the aluminum finish on parts of the Cosmos II is nice, it's also prone to scratching.

In the reviewer's guide Cooler Master also tells us not to move the case by sliding it along the two bottom rails as it will damage the rails, but that seems ludicrous when the case is so heavy to begin with. I know it's counterintuitive to complain about both the weight and the use of plastic in this enclosure when the plastic is helping keep the weight down, but I feel that speaks to larger issues with the overall design. If you're not planning on moving the Cosmos II very often (and who would?) I can see where this won't be as much of a problem, but keep in mind that the dimensions of the case itself are enormous in the first place.

Introducing the Cooler Master Cosmos II Assembling the Cooler Master Cosmos II
POST A COMMENT

53 Comments

View All Comments

  • GoGamerPro - Tuesday, February 7, 2012 - link

    I have games and computers for sale at http://gogamerpro.com Reply
  • arijit.ray81 - Sunday, July 28, 2013 - link

    The X-Dock DOES NOT take up 2 (TWO) 5.25" bays. It takes up about 1.5 (One & Half) of them. I know we can swap them out. However, I'm looking for suitable front panel replacement to put in there. I cant find anything that will fit in that slot. Any suggestions? Reply
  • arijit.ray81 - Friday, October 3, 2014 - link

    How much spacing is there between the motherboard & top? Can we mount a H110? Reply

Log in

Don't have an account? Sign up now