On the back of Intel’s muted launch for the Xeon E3-1200 v5 platform, the server based business units from normal motherboards consumer facing companies are announcing their C230 series. We covered GIGABYTE Server’s offering in a previous pipeline post, and next up comes ASRock Rack with ATX, microATX and mini-ITX offerings for workstations set up for server-based airflow.

C236 WS

First up is the full ATX model, giving support for dual PCIe co-processors at PCIe 3.0 x8/x8, dual Intel networking (I210 and I219), another PCIe 3.0 x4 slot from the chipset, a total of eight SATA ports with SATA Express in there as well, an onboard USB 3.0 Type-A port and eight other USB 3.0 ports through two headers and a four ports on the rear panel.

Compared to the consumer ASRock motherboards, this is eminently more clinical and aimed at its specific market – there is low end onboard audio (ALC662 or lower), COM and TPM support, display outputs and PCIe to PCI bridges for legacy connections.

C236M WS (link)

The micro-ATX member of this family carries over a number of features, such as the dual networking (this time I219-LM and I210) and eight SATA ports, but also implements an M.2 connector and a SATA DOM. Audio is boosted up to at least the ALC892 with 5.1 support, and the power delivery on the processor gets a heatsink for good measure. Perhaps surprisingly we see a total of six fan headers as well.

Despite the layout of the PCIe slots, the bottom open-ended x8 is part of the CPU lanes, offering x8/x8 configuration with a PCIe 3.0 x4 at the top from the chipset. Unfortunately, despite the free PCIe lanes in the system, that M.2 slot is only geared for PCIe 3.0 x1 bandwidth.

C236 WSI (link)

Similar to the boards from GIGABYTE Server, the smaller mini-ITX one is the more interesting out of the set. Here’s a small board with support for up to 32GB of ECC DDR4 memory, a total of eight SATA ports, dual network controllers (again I219 and I210), a full PCIe 3.0 x16 and a rear-IO COM header.

There’s an interesting large gap in the bottom left however, showing solder pads but no integrated chip. The size of the pad suggests that there is room here for an Alpine Ridge controller, suggesting that in the future there might be a version with either USB 3.1 or Thunderbolt 3.

Availability of these motherboards will be dependent on B2B distribution channels, although we might see one or two filter into commercial channels as well.

Source: ASRock Rack

POST A COMMENT

17 Comments

View All Comments

  • BobSwi - Tuesday, October 20, 2015 - link

    On the ITX board, naybe that's a spot for a SAS controller. Reply
  • extide - Tuesday, October 20, 2015 - link

    That's possible, because it looks like there is a spot for the header in the middle of those SATA ports. Reply
  • ZeDestructor - Tuesday, October 20, 2015 - link

    That looks like an M.2 header, not an SFF-8087 header pad (two holes to mount the M.2 header, plus third screwhole further down) Reply
  • ZeDestructor - Tuesday, October 20, 2015 - link

    The M2_1 label is also a bit of a dead giveaway for what is supposed to go there :P Reply
  • ZeDestructor - Tuesday, October 20, 2015 - link

    I don't think so, since there's no room to put in more SAS/SATA ports.

    I'd say BMC/IPMI, but no pads for memory and somewhat far from the ethernet ports. Of course, memory chips could be on the back, so there's that.
    Reply
  • ZeDestructor - Tuesday, October 20, 2015 - link

    Some staring later, and it definitely looks like a pad for a BMC, from the BMC_D151 (I think that's what it says) label, right under the PCIe port to the right of the sticker - it's fairly common to move labels around like that if there's components in the way. The real trick is matching the bits... Reply
  • legolasyiu - Thursday, November 19, 2015 - link

    ASUS P10S-V/4L has more PCI slots and LAN ports and even supports M.2 Reply

Log in

Don't have an account? Sign up now