It's been nearly two years to the day since NZXT last released a motherboard, which was the Z370 N7. NZXT initially used ECS as its motherboard OEM, but has opted to use ASRock this time round for a new N7 model. This has the same N7 infused armor, albeit using a combined metal and plastic instead of just metal which does reduce the overall cost. Aiming for the mid-range market, NZXT's N7 Z490 features 2.5 GbE, Wi-Fi 6, dual M.2, and four SATA ports, and we give it our focus in this review.

The N7 Z490: Going For Mass Effect

At the beginning of September, NZXT reached out to me explaining that they intended to launch a new motherboard into an already cramped Z490 market. One of the elements NZXT wanted to address over its motherboard offerings was the firmware and overclocking, given that ECS isn't really a popular name on those two fronts. This time around, NZXT has leveraged ASRock's services for the underlying platform, on top of which NZXT has layered its own styling and form.

Armed and equipped with a reasonable mid-ranged feature set, the NZXT N7 Z490 includes a premium HD audio codec, combined with 2.5 GbE and an Intel Wi-Fi 6 interface. Perhaps one of the most notable features is the boards full cover armor plating (plastic and metal), which users familiar with NZXT's previous motherboards will recognize. It stretches across the entirety of the PCB, only showing the CPU socket area, memory slots, and the top and bottom edges of the board.

Looking at memory support closer, the N7 Z490 includes the capacity to install up to 128 GB, with speeds of up to DDR4-4266 supported. This is a couple of pegs lower than other models on the market, but the likelihood of regular users opting for higher speeds than this is likely to be slim due to cost. The board uses two PCIe 3.0 x4 M.2 slots for storage, with four SATA ports available. On the rear panel, the N7 Z490 uses just two USB 3.2 G2 ports, a single Type-C, and just one Type-A, with two USB 3.2 G1 Type-A and two USB 2.0 ports.

In our performance testing, the N7 Z490 performed and behaved like any other Z490 board we've tested from ASRock. We saw the N7 Z490 do well in our Non-UEFI POST time test, get a good result in our DPC latency test, and observed competitive performance in our computational and gaming benchmarks. Overall, for any stock level performance, it was hard to find fault with the board.

For overclocking, the NZXT N7 Z490 performed better than any NZXT board I've tested so far (I've owned all of them). Similar to other ASRock models, when adjusting the CPU VCore voltage in the firmware, it reverts the LLC profile to level 1 for tighter and aggressive VDroop control. It feels as if the firmware isn't quite polished to the standard we would expect for release - in our manual overclock testing, setting 1.250 V in the firmware at 4.8 GHz, all cores gave us a load VCore of 1.384 V, which is way too much. This presented even more problems at higher overclocks and caused a lot of downclocking, which skewed our results, with a possible issue within the board's loadline calibration profile settings. More info on this in the review.

The NZXT N7 Z490 has an MSRP of $230, which puts it in direct competition with models such as the ASRock Z490 PG Velocita ($235), the GIGABYTE Z490 Aorus Elite AC ($220), and the ASUS Prime Z490-A ($230). All of the competing models include support for faster memory, more SATA ports, with the ASUS model offering better USB 3.2 G2 connectivity. What NZXT has squarely in its favor is a competitive networking combination, with a unique and uniformed aesthetic due to the PCB armor, which looks great. The crux of the matter is whether or not the NZXT N7 Z490 steps up to the challenge in our test suite.

Read on for our extended analysis and comparison tests.

Visual Inspection
Comments Locked

45 Comments

View All Comments

  • jabber - Thursday, October 8, 2020 - link

    Now if only we could get a new power delivery/connector standard and we could move on from the 20th century.
  • PeachNCream - Friday, October 9, 2020 - link

    Shroud covering the PCB seems functionally unnecessary and likely adds cost or causes the manufacturer to believe the covering gives the motherboard a more "premium" feel and therefore somehow justifies an increased MSRP. Either way, I would prefer a motherboard that focuses strictly on functionality and value akin to those you find in OEM business desktop PCs that are still available five or more years later as refurb/resales on ebay. Give me that kind of look and reliability instead of a childish gimmick.
  • 80-wattHamster - Saturday, October 10, 2020 - link

    Sounds like you want an ASUS CSM board. https://www.asus.com/us/Motherboards/CSM-Corporate...
  • gayathri - Tuesday, October 13, 2020 - link

    <a href="https://liageorson.com/">computer hardware</a>
  • gayathri - Tuesday, October 13, 2020 - link

    <a href="https://liageorson.com//">computer hardware</a>

Log in

Don't have an account? Sign up now