The NZXT N7 Z490 Motherboard Review: From A Different Direction
by Gavin Bonshor on October 7, 2020 10:30 AM EST- Posted in
- Motherboards
- Intel
- ASRock
- NZXT
- Z490
- Comet Lake
- Intel 10th Gen
- i7-10700K
- N7 Z490
It's been nearly two years to the day since NZXT last released a motherboard, which was the Z370 N7. NZXT initially used ECS as its motherboard OEM, but has opted to use ASRock this time round for a new N7 model. This has the same N7 infused armor, albeit using a combined metal and plastic instead of just metal which does reduce the overall cost. Aiming for the mid-range market, NZXT's N7 Z490 features 2.5 GbE, Wi-Fi 6, dual M.2, and four SATA ports, and we give it our focus in this review.
The N7 Z490: Going For Mass Effect
At the beginning of September, NZXT reached out to me explaining that they intended to launch a new motherboard into an already cramped Z490 market. One of the elements NZXT wanted to address over its motherboard offerings was the firmware and overclocking, given that ECS isn't really a popular name on those two fronts. This time around, NZXT has leveraged ASRock's services for the underlying platform, on top of which NZXT has layered its own styling and form.
Armed and equipped with a reasonable mid-ranged feature set, the NZXT N7 Z490 includes a premium HD audio codec, combined with 2.5 GbE and an Intel Wi-Fi 6 interface. Perhaps one of the most notable features is the boards full cover armor plating (plastic and metal), which users familiar with NZXT's previous motherboards will recognize. It stretches across the entirety of the PCB, only showing the CPU socket area, memory slots, and the top and bottom edges of the board.
Looking at memory support closer, the N7 Z490 includes the capacity to install up to 128 GB, with speeds of up to DDR4-4266 supported. This is a couple of pegs lower than other models on the market, but the likelihood of regular users opting for higher speeds than this is likely to be slim due to cost. The board uses two PCIe 3.0 x4 M.2 slots for storage, with four SATA ports available. On the rear panel, the N7 Z490 uses just two USB 3.2 G2 ports, a single Type-C, and just one Type-A, with two USB 3.2 G1 Type-A and two USB 2.0 ports.
In our performance testing, the N7 Z490 performed and behaved like any other Z490 board we've tested from ASRock. We saw the N7 Z490 do well in our Non-UEFI POST time test, get a good result in our DPC latency test, and observed competitive performance in our computational and gaming benchmarks. Overall, for any stock level performance, it was hard to find fault with the board.
For overclocking, the NZXT N7 Z490 performed better than any NZXT board I've tested so far (I've owned all of them). Similar to other ASRock models, when adjusting the CPU VCore voltage in the firmware, it reverts the LLC profile to level 1 for tighter and aggressive VDroop control. It feels as if the firmware isn't quite polished to the standard we would expect for release - in our manual overclock testing, setting 1.250 V in the firmware at 4.8 GHz, all cores gave us a load VCore of 1.384 V, which is way too much. This presented even more problems at higher overclocks and caused a lot of downclocking, which skewed our results, with a possible issue within the board's loadline calibration profile settings. More info on this in the review.
The NZXT N7 Z490 has an MSRP of $230, which puts it in direct competition with models such as the ASRock Z490 PG Velocita ($235), the GIGABYTE Z490 Aorus Elite AC ($220), and the ASUS Prime Z490-A ($230). All of the competing models include support for faster memory, more SATA ports, with the ASUS model offering better USB 3.2 G2 connectivity. What NZXT has squarely in its favor is a competitive networking combination, with a unique and uniformed aesthetic due to the PCB armor, which looks great. The crux of the matter is whether or not the NZXT N7 Z490 steps up to the challenge in our test suite.
Read on for our extended analysis and comparison tests.
45 Comments
View All Comments
Gigaplex - Wednesday, October 7, 2020 - link
Can we please stop calling these stupid shrouds that trap heat "armor"?stephenbrooks - Thursday, October 8, 2020 - link
When I saw this I was hoping it was all metal and the components all had heatsinks bonded to it (so it acts as a huge heat sink), but obviously not...s.yu - Thursday, October 8, 2020 - link
All plastic would be thoroughly disappointing.AlexTopfer - Wednesday, October 7, 2020 - link
What does this 'armour' do? And why do you need to armour a motherboard, wouldn't you armour the case?Or is it designed to protect against spalling inside an armoured cases?
Can you please test the armour too? What caliber will it protect against?
Tomatotech - Friday, October 9, 2020 - link
It’s for looks. Just like tacti-cool.My PCs are little black or silver ITX boxes, but if I was building an art piece I’d be tempted to use something like this if I wasn’t going for the cables everywhere junk-punk style.
wolfman3k5 - Thursday, October 8, 2020 - link
They're mediocre junk. Gigabyte, ASUS or MSI, even EVGA, they all make decent motherboards. NZXT should stick to cases, LEDs and AIOs.selenite - Thursday, October 8, 2020 - link
The motherboard, including SSDs is covered in metal and plastic, restricting the airflow to the board's surface, PCH heatsink and SSDs/SSD heatsinks. VRM heatsinks, hollowed out to improve the airflow, but no actual fan that would send some air into what appears to be an L-shaped duct. All of this prettiness is inside the case.A hideous cutout for the USB-C connector at the back. That one is outside the case.
¯\_(ツ)_/¯
Tomatotech - Friday, October 9, 2020 - link
Ouch that C cutout is terrible. It looks like it might be for some kind of locking USB-C connector but I can’t find anything that would fit it. Hopefully they will fix it in a revision.I have an ancient cheap gigabyte ITX mobo with an i3-6100 in it that has a perfectly formed usb c connector & cutout in the backboard. It isn’t hard.
nunya112 - Thursday, October 8, 2020 - link
Asrock will probably blacklist you for not being 100% positive in this review. Just wanted to let you know :)hanselltc - Thursday, October 8, 2020 - link
Wrong platform, wrong time, and definitely the wrong feature set -- at least when you only count the working features.